product Data
Primers
Primers as surface preparation are an intricate part of any fluid applied roofing and waterproofing system. Their fundamental purpose is to assist adhesion to a particular substrate or existing roof system prior to application of RMI thus limiting ensure limiting moisture migration from the underlying substrate or existing roof system. Unchecked moisture migration from the underside could lead to delamination of the new fluid applied system.
RMI primers have been formulated for specific applications and substrates. RMI requires both moisture & adhesion testing prior to new system installation. These tests determine how much or how many coats of a specific primer are required to function properly based upon tested field conditions.
When in doubt as to a particular substrate or project specific application, contact RMI Technical Services.
RMI - PRIME 301 A
- Waterborne modified acrylic neoprene asphalt primer prior to application of liquid applied acrylic roof coatings as RMI-301A-HT.
- Odorless.
- Zero VOC.
- Cure rate will vary depending upon temperature, humidity and wind for local conditions. Allow primed surface to be dry to touch before application of additional materials.
- Structural Concrete.
- Lightweight Insulating Concrete (LWIC).
- Spray Polyurethane Foam (SPF).
- Asphalt Built-up Roofing (BUR).
- Modified Bitumen (SBS & APP).
- Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters).
- Single Ply (EPDM, PVC, TPO, Hypalon).
- Wood (Nailers, Support Blocks).
- Silicone.
- Coal Tar.
RMI - PRIME PLUS
- Fluid applied single component aromatic primer to provide adhesion for RMI products as "RMI Flex" vapor barrier.
- Low VOC: Has moderate odor during application.
- Required for application of "RMI Flex" unless otherwise approved by RMI Technical Services.
- Cure rate will vary depending upon temperature, humidity and wind for local conditions. Allow primed surface to be dry to touch before application of additional materials.
- Structural Concrete.
- Lightweight Insulating Concrete (LWIC).
- Spray Polyurethane Foam (SPF).
- Asphalt Built-Up Roofing (BUR).
- Modified Bitumen (SBS & APP).
- Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters).
- Single Ply (EPDM, PVC, TPO, Hypalon)
- Wood (Nailers, Support Blocks)
- Silicone
- Coal Tar.
RMI - PRIME RSPF
- Waterborne modified acrylic primer prior to application of RMI-RSPF monolithic, high R value, high density, high compressive value tapering insulating substrate for the application of RMI systems.
- Odorless.
- Zero VOC.
- Cure rate will vary depending upon temperature, humidity and wind for local conditions. Allow primed surface to be dry to touch before application of additional materials.
- Structural Concrete.
- Lightweight Insulating Concrete (LWIC).
- Spray Polyurethane Foam (SPF).
- Asphalt Built-Up Roofing (BUR).
- Modified Bitumen (SBS & APP).
- Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters).
- Wood (Nailers, Support Blocks).
- Silicone.
- Coal Tar.
RMI FLEX
- Two part catalyzed Polyglycol rubber, 100% solids, solvent free, non-breathable vapor retarder liquid applied membrane used as a base coat or flashing membrane for application in multiple roofing and waterproofing component systems. UV exposure applications require RMI liquid applied roof coatings.
- Fluid Applied Membrane Perm rating: Non Breathable per Permeance testing.
- While many fluid applied membranes have excellent elongation properties, RMI Flex has 100% memory.
- Ideal for both extreme high and low temperature applications.
- Does not require reinforcing fabrics.
- Ideal for both vertical and horizontal applications.
- Exceptional dry and cure times make it impervious to rain within 30 minutes depending on ambient temperature.
- Same day surface wear coat applications.
- Brush, roller or spray applied.
- Structural Concrete.
- Lightweight Insulating Concrete (LWIC)
- Spray Polyurethane Foam (SPF).
- Asphalt Built-Up Roofing (BUR).
- Modified Bitumen (SBS & APP).
- Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters).
- Single Ply (EPDM, PVC, TPO, Hypalon).
- Wood (Nailers, Support Blocks)
- Silicone.
- Coal Tar.
- Not intended as an unprotected finished traffic or pedestrian walkway.
SPRAY POLYURETHANE FOAM INSULATION
- Two-component, closed-cell, polyurethane foam system, designed for spray applications. "A" component is a polymeric disocyanate. "B" component is a combination of polyols, catalytic agents and non-ozone depleting HFC-245fa blowing agent.
- Used as monolithic, high R value, high density, high compressive value tapering substrate for the application of RMI systems.
- RMI has developed a proprietary "gasket flashing system" utilizing RMI Flex fluid applied non-breathable less than 1 perm membrane with 500+% elongation and 100% memory to provide a double floating seal at all penetrations, transitions, curbs, walls and perimeter. The net result is a true monolithic tapered insulation with superior flashings than conventional board stock and roll sheet membranes.
- It can be surfaced with or without RMI Flex as required. One of our liquid applied roof coatings is required to complete the system.
- Compressive value significantly higher than conventional board stock insulation when combined with RMI Flex provides one of the most hail resistant roof systems available today.
- Structural Concrete
- Lightweight Insulating Concrete (LWIC)
- Gypsum Decks
- Tectum Decks
- Existing SPF
- Asphalt Built Up Roofing (BUR)
- Plywood Decks
- Steel Roof Decks
- Metal Roof Panels
- Modified Bitumen (APP & SBS)
- Single Ply
- Silicone.
- Coal Tar.
- Not intended as an unprotected finished traffic or pedestrian walkway.
RMI THANE
- A silver high solid, low VOC based, single component urethane (flexible) liquid applied (radiant barrier) roof coating for either stand-alone application or over RMI-Flex fluid applied membrane for a finished installation.
- Liquid Applied Roof Coating Perm rating: Breathable per Permeability testing.
- Contains higher percent of polished flake aluminum.
- May be used as a rust inhibitor to prevent further oxidation. Resistant but not impervious to surface contaminants.
- Low permeability than typical water based elastomeric coating.
- Durable wear surface.
- Ideal for both extreme high and low temperature applications.
- Ideal for both vertical and horizontal applications.
- Brush, roller or spray applied.
- Structural Concrete.
- Spray Polyurethane Foam (SPF).
- Asphalt Built-Up Roofing (BUR).
- Modified Bitumen (SBS & APP).
- Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters).
- Single Ply (EPDM, PVC, TPO, Hypalon).
- Silicone.
- Coal Tar.
- Not intended as an unprotected finished traffic or pedestrian walkway.
RMI WHITE 301-A-HT
- A White (available in colors), high-solids, high tensile, heat-resistant, single component water-borne liquid applied acrylic elastomeric roof coating for either stand-alone application over SPF and/or over non-breathable RMI-Flex fluid applied membrane for a finished installation.
- Liquid Applied Roof Coating Perm rating: Breathable-per Permeability testing.
- Durable wear surface.
- Ideal for both vertical and horizontal applications.
- Brush, roller or spray applied
- Structural Concrete.
- Spray Polyurethane Foam.
- Asphalt Built-Up Roofing (BUR).
- Modified Bitumen (SBS & APP).
- Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters).
- Silicone.
- Coal Tar.
- Not intended as an unprotected finished traffic or pedestrian walkway.
WHITE PLUS
- A bright white high solid, low VOC based, two component urethane (flexible) liquid applied (radiant barrier) roof coating for either stand-alone application or over RMI-Flex non-breathable fluid applied membrane for a finished installation.
- Liquid Applied Roof Coating Perm rating: Breathable-per Permeability testing.
- High solid, low VOC based, single component urethane (flexible) liquid applied radiant barrier surface-wear coating for either stand-alone application or over RMI Flex vapor barrier for a finished installation.
- Low permeability than typical water based elastomeric or urethane coatings.
- Durable wear surface.
- Ideal for both vertical and horizontal applications.
- Brush, roller or spray applied.
- Structural Concrete.
- Spray Polyurethane Foam (SPF).
- Asphalt Built-Up Roofing (BUR).
- Modified Bitumen (SBS & APP).
- Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters).
- Silicone.
- Coal Tar.
- Not intended as an unprotected finished traffic or pedestrian walkway.
direct product purchases
Our RMI-Flex Product
RoofMart International (RMI) manufactures high solid, low permeance fluid-applied roofing and waterproofing systems to renovate existing commercial and industrial rooftops and building envelope applications.
It all starts with a non-breathable liquid applied membrane whose performance matches roll sheet Type I vapor retarders. It forms a durable, seamless monolithic membrane with superior adhesion conforming to existing roofs or substrate surfaces with same-day curing for a finished application or a base for liquid applied roof coatings. RMI also provides highly weather-resistant, low perm liquid-applied roof coatings and rigid spray polyurethane foams.
RMI works directly with roofing contractors, architects, consultants, commercial and industrial building owners, and property management companies to provide rooftop waterproofing solutions for: • Airports • Auditoriums • Clinics • Convention Centers • Federal/State Government • Grocery Stores • Gymnasiums • Hospitals/Healthcare • Hotels/Motels • Manufacturing Facilities • Nursing Homes • Office Spaces • Restaurants • Schools/Colleges • Shopping Centers • Silos • Storage Facilities • Warehouses
RMI offers real world-sustainable roofing solutions by conducting forensic project evaluations to provide the best condition-specific solution for your personal asset management needs. Put our 40+ year history to work and contact us to determine if we are the right fit for your project.
• Two-part catalyzed Polyglycol rubber, 100% solids, solvent free, non-breathable vapor retarder liquid applied membrane used as a base coat or flashing membrane for application in multiple roofing and waterproofing component systems.
• Fluid Applied Membrane Perm rating: Non-Breathable per Permeance testing. • While many fluid applied membranes have excellent elongation properties, RMI Flex has 100% memory. • Ideal for both extreme high and low temperature applications. • Does not require reinforcing fabrics. • Ideal for both vertical and horizontal applications. • Exceptional dry and cure times make it impervious to rain within 30 minutes depending on ambient temperature. • Same day surface wear coat applications. • Brush, roller or spray applied.
RMI works directly with roofing contractors, architects, consultants, commercial and industrial building owners, and property management companies to provide rooftop waterproofing solutions for: • Airports • Auditoriums • Clinics • Convention Centers • Federal/State Government • Grocery Stores • Gymnasiums • Hospitals/Healthcare • Hotels/Motels • Manufacturing Facilities • Nursing Homes • Office Spaces • Restaurants • Schools/Colleges • Shopping Centers • Silos • Storage Facilities • Warehouses
RMI offers real world-sustainable roofing solutions by conducting forensic project evaluations to provide the best condition-specific solution for your personal asset management needs. Put our 40+ year history to work and contact us to determine if we are the right fit for your project.
• Two-part catalyzed Polyglycol rubber, 100% solids, solvent free, non-breathable vapor retarder liquid applied membrane used as a base coat or flashing membrane for application in multiple roofing and waterproofing component systems. • Fluid Applied Membrane Perm rating: Non-Breathable per Permeance testing. • While many fluid applied membranes have excellent elongation properties, RMI Flex has 100% memory. • Ideal for both extreme high and low temperature applications. • Does not require reinforcing fabrics. • Ideal for both vertical and horizontal applications. • Exceptional dry and cure times make it impervious to rain within 30 minutes depending on ambient temperature. • Same day surface wear coat applications. • Brush, roller or spray applied.
Our RMI-Thane Product
• A silver high solid, low VOC based, single component urethane (flexible) liquid applied (radiant barrier) roof coating for either stand-alone application or over RMI-Flex fluid applied membrane for a finished installation. • Liquid Applied Roof Coating Perm rating: Breathable per Permeability testing. • Contains higher percent of polished flake aluminum. • May be used as a rust inhibitor to prevent further oxidation. Resistant but not impervious to surface contaminants. • Low permeability than typical water based elastomeric coating. • Durable wear surface. • Ideal for both extreme high and low temperature applications. • Ideal for both vertical and horizontal applications. • Brush, roller or spray applied.
Stand-Alone Substrates: • Structural Concrete. • Spray Polyurethane Foam (SPF). • Asphalt Built-Up Roofing (BUR). • Modified Bitumen (SBS & APP). • Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters). • Single Ply (EPDM, PVC, TPO, Hypalon).
Incompatible Substrates: • Silicone. • Coal Tar. • Not intended as an unprotected finished traffic or pedestrian walkway.
Our RMI-White Product
Contact RMI for applicable substrates and applications. • Liquid Applied Roof Coating Perm rating: Breathable-per Permeability testing. • Durable wear surface. • Ideal for both vertical and horizontal applications. • Brush, roller or spray applied.
Stand-Alone Substrates: • Structural Concrete. • Spray Polyurethane Foam (SPF). • Asphalt Built-Up Roofing (BUR). • Modified Bitumen (SBS & APP). • Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters). • Single Ply (EPDM, PVC, TPO, Hypalon).
Incompatible Substrates: • Silicone. • Coal Tar. • Not intended as an unprotected finished traffic or pedestrian walkway.
Our RMI-Primer Products
Primers as surface preparation are an intricate part of any fluid applied roofing and waterproofing system. Their fundamental purpose is to assist adhesion to a particular substrate or existing roof system prior to application of RMI thus ensure limiting moisture migration from the underlying substrate or existing roof system. Unchecked moisture migration from the underside could lead to delamination of the new fluid applied system. RMI primers have been formulated for specific applications and substrates.
RMI requires both moisture & adhesion testing prior to new system installation. These tests determine how much or how many coats of a specific primer are required to function properly based upon tested field conditions. When in doubt as to a particular substrate or project specific application, contact RMI Technical Services.
Contact RMI for applicable substrates and applications. • Fluid applied single component aromatic primer to provide adhesion for RMI products as "RMI Flex" vapor barrier. • Low VOC: Has moderate odor during application. • Required for application of "RMI Flex" unless otherwise approved by RMI Technical Services. • Cure rate will vary depending upon temperature, humidity and wind for local conditions. Allow primed surface to be dry to touch before application of additional materials.
Stand-Alone Substrates: • Structural Concrete. • Spray Polyurethane Foam (SPF). • Asphalt Built-Up Roofing (BUR). • Modified Bitumen (SBS & APP). • Metal (Ducts, Roof Panels, Wall Panels, Coping, Flashings, Gutters). • Single Ply (EPDM, PVC, TPO, Hypalon). • Lightweight Insulating Concrete (LWIC). • Wood (Nailers, Support Blocks).
Incompatible Substrates: • Silicone. • Coal Tar.
AT RMI, Performance isn't "optional".
Sales
Canada
Technical
.svg){kind=icon}